Got to meet a few guys from here and css also.
Full Version: WARNING: DANGER TO MANIFOLD
Got one decent run in. Then Robbie showed up just in time to see the manifold let loose. Guess it's payback for laughing at him when his did the same thing last year.
Got to meet a few guys from here and css also.
Got to meet a few guys from here and css also.
damn son! so what mani is in store for her now?
at least you tow that bitch there!
at least you tow that bitch there!
QUOTE(93 red ls @ Mar 24 2007, 07:22 PM) 
damn son! so what mani is in store for her now?
at least you tow that bitch there!
A little welding should do it. And an extra brace or two and probably ditch the exhaust system.
damn that sucks...maybe honda will goodwill it haha
nice to meet you...sucks our dealerships are rivals haha
nice to meet you...sucks our dealerships are rivals haha
QUOTE(jdmlovingcrx @ Mar 24 2007, 08:02 PM)
damn that sucks...maybe honda will goodwill it haha
LOL Wouldn't be too unreasonable compared to some of the stuff people expect.
So what did you run on the first pass?
QUOTE(D-Atk @ Mar 25 2007, 09:48 AM)
So what did you run on the first pass?
11.6@126 on 24 psi. It spun on the rev limiter through 2nd because i forgot to launch on low boost.
A funny thing: yesterday I wasn't bothered about it breaking, today i'm all bummed out.
Dont know why; it's odd.
My car blew up there yesterday, so you got off easy. I'm down in the dumps today too. Oh well. It is a good excuse to order thst sleeved block and 84.5mm pistons.
QUOTE(shakenbake @ Mar 25 2007, 03:03 PM)
My car blew up there yesterday, so you got off easy. I'm down in the dumps today too. Oh well. It is a good excuse to order thst sleeved block and 84.5mm pistons.
damn brad!!! that sucks man! OH SNAP THOUGH SLEEVED BLIZOCK!
QUOTE(shakenbake @ Mar 25 2007, 04:03 PM)
My car blew up there yesterday, so you got off easy. I'm down in the dumps today too. Oh well. It is a good excuse to order thst sleeved block and 84.5mm pistons.
Yea, mines no big deal.
I was hoping you'd get by with just a headgasket.
man two big dogs breaking shit this early in the year! SAVE IT FOR LATER GUYS hhaha...
if you guys go to tri state again let me know ill stop and watch or run the ef hahaha
if you guys go to tri state again let me know ill stop and watch or run the ef hahaha
Sucks about your cars 
Nice meating you two, Chiovnidca and shakenbake. Hope you guys get them running soon
Nice meating you two, Chiovnidca and shakenbake. Hope you guys get them running soon
QUOTE(shakenbake @ Mar 25 2007, 04:03 PM)
My car blew up there yesterday, so you got off easy. I'm down in the dumps today too. Oh well. It is a good excuse to order thst sleeved block and 84.5mm pistons.
Ouch, you had a solid setup... What broke?
Dont worry robin, that first pass is a good start to a good year for ya. If you need anything holler at me.
Thows welds are f-ing tiny! its a wonder it lasted as long as it did.
QUOTE(HI OFECR @ Mar 25 2007, 10:21 PM)
Thows welds are f-ing tiny! its a wonder it lasted as long as it did.
Looking at it the flange wasn't welded well on the sides, that's where it started cracking. The rest of the manifold looks fine. (to me anyway) I'll hit it with the mig.
QUOTE(widebody @ Mar 25 2007, 10:04 PM)
Ouch, you had a solid setup... What broke?
Dont worry robin, that first pass is a good start to a good year for ya. If you need anything holler at me.
I'm guessing I cracked a sleeve, but I haven't ripped it apart yet.
just be glad the manifold blew before your floor board shot out. then all hell would of broke loose
Ouch. What kind of manifold was it anyways?
QUOTE(BiggJohnson06 @ Mar 26 2007, 08:05 AM)
just be glad the manifold blew before your floor board shot out. then all hell would of broke loose
Haha I was thinking that just after I saw the crack.
QUOTE(McLude @ Mar 26 2007, 09:57 AM)
Ouch. What kind of manifold was it anyways?
A guy on ebay made em in his basement shop. That's the story he gave anyway. It was reasonably priced.
This is a "lo-fi" version of our main content. To view the full version with more information, formatting and images, please click here.